Polishing wood to

Development of the wood, further emphasizing the typical characters, change the color and protection in various ways also exist. One of them is polishing. Thoroughly clean the raw wood before finishing. Dust, glue, resin, dirt and stains with warm water and soap remove the grain. Turpentine salt dissolves stubborn stains. Board

Always brush in the direction of the vessel.

Soaking:

Soap on the wet wood, wood fibers swell. This wooden structure is important for the small damage dengilenmesi.
During the cleaning and wetting sure to moisten all with an equal amount of points. Too much liquid, a sponge and squeeze with your hands by releasing taken. Wood surface and press release.

After soaking the wood to dry thoroughly so do not start working.

Sanding:

After drying of wood are sanded. Matter how thin abrasive surface is so smooth. Scroll to the end step: coarse sandpaper (number 120), medium sand (150 numbers) and fine sandpaper (180 number). Using a sand wedge in hand, try. Timber vessels, always in the direction and by applying light pressure bbir scroll.

Sanding dust carefully with a dry brush to clear. For which you want to polish the end of the wood in contact with your skin should not in any way. Traces of oil stains will remain on board.

Preparation of polish:

You need to polish those are: polishing powder or liquid wax, non-metal brush, sponge, rubber, plastic containers or plastic buckets and clothing as eldivenler.Iş a long rubber apron and rubber boots to measure you should use. In order to polish the polishing liquid is a lot, so empty as possible, keep your work area and the floor covered with newspapers, for example, or tala. In this way, the polishing liquid to flow as a result of the jump or you will avoid problems. Polishing in the open air if possible or try keeping the windows open. Use salt-based non-chrome polish - it waxes and polishes olabilmektedir.Ahşap harmful, depending on your taste in shades of various colors are sold. Can be found in liquid or powder lacquers. Powder finish packing instructions by water soluble is liquid polish is for use hazırdır.Yüksek rate resin containing wood, eg pine, the finish before the necessary resin as a resin, removing the removal must, or resin, wood-sided spots leave. To finish each wood species will react differently. Before it and the results of an experiment to see if you like it.

Driving of the liquid polish:

Do not polish very quickly. Saturated with metal polish with a brush of the crawl, the fluid running immediately. Therefore, a sufficient amount of liquid wax from the above, the following principles hazırlamalısınız.Düşey standing parts are working correctly. Thus, dripping wax, does not create a second floor because it can not immediately established. Polished cutting edge and therefore more likely to absorb more dark matter. Useful information: moisten edges with water beforehand, so you'll get a homogeneous result. Soaking and grinding process is running in case you do if you detect these spots, spots, still wet, clear lacquer. Stains, sand, and on them once a genius, polish sürün.Birbiriyle linked to the surfaces if you work, polishing the same person tarafındanyapılması is advised, because the wax during that everyone own a hand operation that konusudur.Cilayı wood fibers in the direction of creep that the fluid of the board all the pores handler could. Here, too slow and too thin strips of wax not to take note. Within a few minutes, longer than polish, hair with a cloth or a sponge, wood, natural wood tones in the direction of progress as a result of the alın.Cila become intense or dark colors can be opened. To be transparent so the wood is polished to earn their own special characteristics. Polish all wood species except larch results give excellent results. Even in the polished wooden surface ikik geliştirebirsiniz: candlelit mat, and then update, or priming. So that the natural beauty of wood to a shine.

And wax Lubrication:

The polished wooden surfaces, candles or oil if they are protected and they shine. Varieties sold in a transparent and liquid pigmented wax, wax or solid, you can choose from. Teams to use only candles made from natural ingredients. Candles, wood is pale almasınıengellememe features. Soft wax,

a cotton cloth and hair, crawling in the direction of wood fibers. You can also use candles in liquid fırçı. By the time a few times the density of colored wax candle artırabilirsiniz.Tipik brightness, surface after drying with a soft cloth to shine If you stronger. The lasting effects of wax to make the process should be renewed occasionally. Originally was developed for teak teak oil in another timber can also provide protection and shine. Linseed oil with a cloth and then carefully crawl this publication. After drying with sand (240-280)

slightly. Sanding dust thoroughly and repeat the oiling process.